How to build up a Face centered central composite design with JMPHey JMP users,
I need to build up a Face centered CDD with 3 factors, each at 3 levels, 2 blocks and 4 center points.
This is how I proceeded:
1) select Classical > Response Surface Design
2) add 3 factors > Continue
3) Here I don't know if I should select "Central Composite Design" or "CDD-orthogonal Blocks" as I need to add one blocking factors with 2 levels however the CDD does not allow me to add blocks and the CDD-orthogonal Blocks gives me one block with 3 levels.
Q1 : How should I proceed ?
Q2 : If I do the same with Custom design as it allows me to add blocks, that means it is no more a classical CDD design right ?
Thanks in advance !
DOERe: How to build up a Face centered central composite design with JMPWhen adding a blocking variable, the block will always be an orthogonal block. This is a good thing! For your situation there is no orthogonal block for two blocks. You need to use 3 blocks. With three blocks your axial points from your face-centered design will all be in the last block. The only blocking possible in the design creation process is a fixed block.
A custom design gives you more flexibility, but it will likely not match the CCD. However, this is where the nature of your blocking variable is important. What is the blocking variable? Blocking variables are also often called "nuisance" variables meaning it is not a factor you wish to study, but due to practical concerns it must change. Therefore, the Custom Designer is set up in such a way that you specify the number of runs per block rather than the number of blocks. Further, the custom designer allows you specify a fixed blocking variable (specific levels of the blocking variable or all possible levels) or a random block (the levels are a random selection from a larger set of possible levels).
There is much more that could be discussed with respect to blocking and the design types, but that would be better left for a design of experiments class.
Re: How to build up a Face centered central composite design with JMPThanks a lot for your answer.
The bloking factor is the membrane as I am considering the use of 2 different membranes for filtration. Does that mean that if I use 3 membranes instead of two, this problem will be resolved?
Another question : when building CCD there are different type to select at the first step, with different center points and blocking (see picture below). I don't understand what is the difference between the 4 CCD.
I was trying to select Central Composite Design with 2 center points and then change "2" per "4" and jmp crushs. So the number of center points is fixed and could not be changed ?
Thank you in advance.
I
Re: How to build up a Face centered central composite design with JMPIf you really want to consider membrane as a block rather than a factor, then using a third membrane would resolve the issue. However, realize that you are treating your membranes as a fixed block, meaning that your conclusions are only good over those three membranes. It sounds to me like the membranes would be better treated as a random block. That would mean using custom design and calling them random and you estimate the variance due to the different membranes. You can change the membranes from fixed to random in the analysis phase of the project, if you want.
As for the differences in the CCDs, there are some slight differences. First, the biggest difference is the number of center points.
The first design is a CCD with 2 center points.
The second design is a CCD with 4 center points which is the number required to achieve a mathematical property called Uniform Precision. However, that Uniform Precision is only achieved if you use the Rotatable axial distance. Since yours will be face-centered, you can ignore the Uniform Precision label.
The third design has a blocking variable, so it is a blocked design. That means that the blocks will be orthogonal. Since there will be 3 blocks, the number of center points should be a multiple of 3 so that they can be evenly distributed through the blocks.
The fourth design has 9 center points. This design would have Uniform Precision AND be orthogonal if you use the default Rotatable axial distance. Since you are not using that, it truly is just 9 center points.
Finally, after choosing your desired CCD (suppose the 2 center point design), you have the option to change the number of center points. You should be able to choose any number you want as long as there is at least one. If JMP crashes when you do this, what version of JMP are you using? If it is 15.2.1 (the latest), you should report it to Tech Support (support@jmp.com). If you are not using the latest version, you should probably upgrade to the latest version.
